Vidgrids » apm connector

apm connector

3DR Radio Telemetry Kit 433Mhz Module Open source for APM 2.5 2.6 2.8

3DR Radio Telemetry Kit 433Mhz Module Open source for APM 2.5 2.6 2.8

41.29 SGD

3DR Radio Telemetry Kit 433Mhz Module Open source for APM 2.5 2.6 2.8 Type: Other Accessories Features: Very small size,light weight 433Mhz frequency band Receiver sensitivity to -117 dBm Transmit power up to 20dBm (100mW) Transparent serial link Air data rates up to 250kbps Range of approx 1 mile with supplied antennas Demonstrated range of several kilometers with a small omni antenna Can be used with a bi-directional amplifier for even more range MAVLink protocol framing and status reporting Frequency hopping spread spectrum (FHSS) Adaptive time division multiplexing (TDM) Support for LBT and AFA Configurable duty cycle Built in error correcting code (can correct up to 25% data bit errors) Open source firmware AT commands for radio configuration RT commands for remote radio configuration Adaptive flow control when used with APM Based on the HopeRF HM-TRP radio module, featuring an SiLabs Si1000 RF microcontroller.

L Connector

L Connector

13.9 USD

The "L" connector from WAC Lighting, is used to join two track sections while making a 90 degree angle turn and can be used to apply power between the joined sections of track. Available in Left-Hand and Right-Hand polarity turns. Polarity grooves are determined by the position of the power connector on the track system. For a detailed chart of polarity grooves with WAC track, please review the following handout . For track systems which are using a Floating Canopy Connector to power the track, the Left hand polarity is recommended. Features: Accepts wires from above the ceiling, with knock out for trade size connector. For use with WAC brand H, L and J series track systems. Available in Black, Brushed Nickel, Dark Bronze and White finishes.

KYDZSuite Connector Hub

KYDZSuite Connector Hub

30.99 USD

The KYDZSuite Hub is central to creating your own space you can attach items at eight different 45 degrees angle increments. Match to other KYDZSuite items including Panels Stabilizer Wings and more. Bottom has slip-resistant rubber stopper. Wooden dowel is made using hard Maple with KYDZTuff finish. Top and bottom connector hubs are made from molded nylon for superior strength. Wooden top cap screws on with friction fit rubber gasket to tightly secure the hub in place. You will need 3 Hubs for the first 2 panels and 1 Hub for each additional panel. Patent pending. Available in 24-1/2ö 29 1/2 ö and 35-1/2ö heights. 2-1/2 wide x 2-1/2 deep.

Monoprice HDMI Connector Male to HDMI Mini Connector Female Adapter

Monoprice HDMI Connector Male to HDMI Mini Connector Female Adapter

14.76 USD

Do you have an existing HDMI cable but need to adapt it to fit into an HDMI Mini Connector?, HDMI the HDMI Logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries, Our HDMI Mini Connector male to HDMI Connector female adapter will convert one of the ends of your HDMI Cable into a HDMI Mini Connector!, Suitable for all devices that support HDMI and the HDMI Mini Connector

EC3 Connector Female - Battery Side

EC3 Connector Female - Battery Side

N/A

EC3 Connector Female - Battery SidePerfect for electric power applications and works withany battery, charger, ESC, Power Meter, etc. Key FeaturesCapable of 60 amps continuously Ergonomically pleasing and easy to grip Protected to avoid shorting and reverse polarity Superior technology suited to today's advanced applications Designed with convenience and reliabilityIncludes:1 x Plastic housing2 x 3.5mm gold plated bullet connectors

EC3 Connector male - Device Side

EC3 Connector male - Device Side

N/A

EC3 Connector Male - Device SidePerfect for electric power applications and works withany battery, charger, ESC, Power Meter, etc. Key FeaturesCapable of 60 amps continuously Ergonomically pleasing and easy to gripProtected to avoid shorting and reverse polaritySuperior technology suited to today's advanced applicationsDesigned with convenience and reliabilityIncludes:1 x Plastic housing2 x 3.5mm gold plated bullet connectors

Gilmour 2939AQ Connector Starter Kit

Gilmour 2939AQ Connector Starter Kit

13.99 USD

Gilmour 2939AQ Connector Starter Kit Features: Connector Starter Kit Provides quick and easy connections to faucet, hose, and hose end accessories 1 female hose end connector with automatic water shut-off 2 male hose end adapters 1 male faucet adapter 1 female faucet connector Impact resistant, rustproof polymer construction Interchangeable with most polymer quick connector systems

High-Line Cross Connector - Conductive

High-Line Cross Connector - Conductive

36.0 USD

The CROSS CONNECTOR is necessary when two non-insulated cable runs are crossing each other. Available in both conductive and non-conductive pieces. Connector creates a conductive bridge between the two cables, while the non-conductive connector prevents accidental contact between two cables. CROSS CONNECTOR is sold individually. 3/8" cable separation. Available in chrome (ch) or matte chrome (mc).

Live End Connector

Live End Connector

9.0 USD

Used for direct wiring from conduit through the ceiling. The Live End Connector from WAC Lighting supplies power through the end of a track. Features: Accepts wires from above the ceiling, with knock out for trade size connector. For use with WAC brand H, L and J series track systems. Available in Black, Brushed Nickel, Dark Bronze and White finishes.

Two Circuit Flexible Connector

Two Circuit Flexible Connector

47.0 USD

The Flexible Track Connector from WAC Lighting, connects two track sections at variable angles from 60eg; to 180eg;. Can be used as a transition from wall-to-wall, wall-to-ceiling, or ceiling-to-ceiling. Features: Accepts wires from above the ceiling, with knock out for trade size connector. Available in Black, Platinum and White finishes.

Progress Lighting P8743 Coupling Connector

Progress Lighting P8743 Coupling Connector

10.62 USD

6" coupling cable connector for adjoining two HAL3 linking cables in White finish.Bulb Included: No Category Group: Undercabinet Category Sub Group: Undercabinet Accessories Collection: Hide-A-Lite III Finish: White, Antique Bronze Height: 0.38 Length: 6.00 Style: Traditional Type: Undercabinet Weight: 0.20 Width: 0.75

X Connector

X Connector

23.9 USD

The X connector from WAC Lighting connects four track sections at 90eg; and allows a "X" shape to be made. Features: Accepts wires from above the ceiling and is a power entry point. For use with WAC brand H, L and J series track systems. Available in Black, Brushed Nickel, Dark Bronze and White finishes.

Boa Track Connector 60-180h

Boa Track Connector 60-180h

204.0 USD

Custom internal angle connector for the BOA track. Angles between 60eg; and 180eg; may be specified in increments of 5eg; when ordering. No additional tools are required for installation, the connector plugs directly into the track. The springs at the ends hold the track firmly in place when attached.

Quilt Ruler Connector(tm)

Quilt Ruler Connector(tm)

11.99 USD

Forget carrying a big 24" ruler to class! Simply take two 12" rulers and the Quilt Ruler Connector™ and turn them into a 24"-long or a 12" square ruler when needed. Made of super tough polycarbonate, the Quilt Ruler Connector™ is virtually unbreakable. 5 3/4"L x 5 1/2"W x 1/2"H.

Two Circuit Live End Connector

Two Circuit Live End Connector

21.0 USD

Used for direct wiring from conduit through the ceiling. The Live End Connector from WAC Lighting supplies power through the end of a track. Features: Accepts wires from above the ceiling, with knock out for trade size connector. Available in Black, Platinum and White finishes.

Fountain Connector

Fountain Connector

6.49 USD

Connect two 2-liter bottles (one filled 1/2 way with water) turn upside down and watch as air lifts the water up higher than its origin and creates an amazing fountain. Water is colored with our Colorations Liquid Watercolor. Note: Two-liter bottles not included.

WAC Lighting JX "X" Connector

WAC Lighting JX "X" Connector

24.5 USD

Used to join four track sections to make an "X" Configuration For use with "J" type systemsFinish: Black, Brushed Nickel, Dark Bronze and White Length: 4-1 4 System Type: J Track Accessory Type: Connectors Voltage: 120, J Track Weight: 0.18 Width: 7-1 8

DEFLECTO AMDOC/6 Dryer Connector (Offset Connector)

DEFLECTO AMDOC/6 Dryer Connector (Offset Connector)

17.16 USD

4" dryer offset connector Fire-resistant Solves tight space venting problems Vertical, horizontal or diagonal installation Fits any type of dryer back Aluminum with .014" - .016" thickness Easy to install Manufacturer Warranty: Ninety Days

Smartenit 8045A EZBreakout Connector

Smartenit 8045A EZBreakout Connector

6.99 USD

This device allows you to easily connect a CAT5 or CAT3 patch cable with its RJ-45 or RJ-11 terminations and split up the wires into screw down terminals. It is ideal for adding a rain sensor or water meter to the EZFlora Irrigation Controller.

Zonyx Flexible Track Connector

Zonyx Flexible Track Connector

76.5 USD

The Zonyx Flexible Track Connector allows the creation of different angles varying from 0 to 180eg;. Technical Specifications: 2400VA 120VAC input Suitable for dry locations only Bendable 0eg; to 180eg; (horizontal) or 0eg; to 90eg; (vertical)

Flex-Line Track Connector

Flex-Line Track Connector

148.5 USD

Connector for Flex-Line tracks where it is necessary to extend the length of the track and to maintain the power supply along the full length. Simple installation requiring the use of the allen wrench; included with each connector.

Two Circuit X Connector

Two Circuit X Connector

47.0 USD

The X connector from WAC Lighting connects four track sections at 90eg; and allows a "X" shape to be made. Features: Accepts wires from above the ceiling and is a power entry point. Available in Black, Platinum and White finishes.

HQmade 1 to 2 RCA Connector Phono Connector Cinch Connector AV Audio Video Stereo Y Splitter Adapter M/F

HQmade 1 to 2 RCA Connector Phono Connector Cinch Connector AV Audio Video Stereo Y Splitter Adapter M/F

2.06 AUD

HQmade 1 to 2 RCA Connector Phono Connector Cinch Connector AV Audio Video Stereo Y Splitter Adapter M/F Type: Component Video Splitters Ports: 2 Input Connector: RCA, Male Output Connector: RCA, Female Maximum Resolutions: None

GW BNC Connector Twist On RG59 CCTV Coax Cable Male Connector - (100 pcs)

GW BNC Connector Twist On RG59 CCTV Coax Cable Male Connector - (100 pcs)

3424.95 INR

GW BNC Connector Twist On RG59 CCTV Coax Cable Male Connector - (100 pcs) Type: Connector Specifications: Male BNC Twist On For RG59 CCTV Cable Package Contents: 100 piece Parts: Free 1 Year Warranty Labor: Free 1 Year Warranty

Orion Sword Flexible Connector

Orion Sword Flexible Connector

37.5 USD

Flexible connector for Orion Sword. Connect two Sword segments at almost any angle with this flexible connector. Technical Specifications: 24V DC rated 96 Watt maximum thru-put Class II rated Suitable for dry locations only.

Boa Track Connector 120h

Boa Track Connector 120h

174.0 USD

A 120eg; internal angle connector for the BOA track. No additional tools are required for installation, the connector plugs directly into the track. The springs at the ends hold the track firmly in place when attached.

Boa Track Connector 135h

Boa Track Connector 135h

174.0 USD

A 135eg; internal angle connector for the BOA track. No additional tools are required for installation, the connector plugs directly into the track. The springs at the ends hold the track firmly in place when attached.

Boa Track Connector 90h

Boa Track Connector 90h

159.0 USD

A 90eg; internal angle connector for the BOA track. No additional tools are required for installation, the connector plugs directly into the track. The springs at the ends hold the track firmly in place when attached.

Boa Track Connector 60h

Boa Track Connector 60h

174.0 USD

A 60eg; internal angle connector for the BOA track. No additional tools are required for installation, the connector plugs directly into the track. The springs at the ends hold the track firmly in place when attached.

Replacement System Connector opladen Block Connector Flex Vergadering voor iPhone 5C (Zwart)

Replacement System Connector opladen Block Connector Flex Vergadering voor iPhone 5C (Zwart)

6.9864678 USD

Dit is een vervangend iPhone 5C systeem connector opladen blok connector flex.Als uw opladen blok connector flex vast komen te zitten of niet goed functioneren, dit is het deel dat u nodig hebt om te vervangen.

Boa Track Connector Inline /Iso

Boa Track Connector Inline /Iso

48.0 USD

A non-conductive connection for two sections of straight BOA track. Pluging directly into the track, the connector isolates the dual circut track into four separate circuts. No additional tools are necessary.

Replacement System Connector Charging Block Connector Flex Assembly for iPhone 5S

Replacement System Connector Charging Block Connector Flex Assembly for iPhone 5S

5.39 Rep

This is a replacement charging block connector flex assembly for the iPhone 5S. If your charging block connector flex get stuck or are not functioning properly, this is the perfect spare part for you.

KYDZSuite Accessories - Wall Connector Post

KYDZSuite Accessories - Wall Connector Post

30.99 USD

Pre-drilled holes and included hardware make it is easy to connect your KYDZSuite components to the wall using the Wall Connector. 3 wide x 1/2 deep. Available in 24-1/2 29-1/2 and 35-1/2 heights.

CERTIFIED APPLIANCE IM120P Polyvinyl Ice Maker Connector (10ft, 1/4" Connector)

CERTIFIED APPLIANCE IM120P Polyvinyl Ice Maker Connector (10ft, 1/4" Connector)

13.56 EUR

CERTIFIED APPLIANCE IM120P Polyvinyl Ice Maker Connector (10ft, 1/4" Connector) Type: Project Lamp Specifications: CERTIFIED APPLIANCE IM120P Polyvinyl Ice Maker Connector (10ft, 1/4" Connector)

I Straight Line Connector

I Straight Line Connector

9.0 USD

Straight line connector used to join two sections of track. Features: For use with WAC brand H, L and J series track systems. Available in Black, Brushed Nickel, Dark Bronze and White finishes.

JST-XHP 2Pin Power Connector

JST-XHP 2Pin Power Connector

N/A

Connector with wire leads 150mm 22 Gauge silicone wireBe sure to check the polarity before splicing.Incorrect polarity can cause permanent damage to a charger or balancer and may cause a fire.

Zonyx 90 Degree Connector

Zonyx 90 Degree Connector

172.5 USD

The Zonyx 90eg Connector can be used for in-line, right angle, rigid conductive connection of two Zonyx track. Technical Specifications: 2400VA 120VAC input Suitable for dry locations only.

Solorailrade; "L" Connector

Solorailrade; "L" Connector

23.9 USD

Connects two sections of rail with electrical continuity. Allows seamless connection of rail sections in a "L" shape. Available in Chrome, Brushed Nickel and Dark Bronze finishes.

Solorailrade; "T" Connector

Solorailrade; "T" Connector

37.0 USD

Connects two sections or rail in a "T" with electrical continuity. Allows for seamless connection of rail sections. Available in Chrome, Brushed Nickel and Dark Bronze finishes.

Zonyx Conductive Track Connector

Zonyx Conductive Track Connector

34.5 USD

The Zonyx Track Connector can be used for in-line, rigid conductive connection of two Zonyx track. Technical Specifications: 2400VA 120VAC input Suitable for dry locations only

HQmade 20 Amp Low Profile MINI Blade Fuses – APM / ATM Automotive Fuse - Order by PCS

HQmade 20 Amp Low Profile MINI Blade Fuses – APM / ATM Automotive Fuse - Order by PCS

0.4 EUR

HQmade 20 Amp Low Profile MINI Blade Fuses – APM / ATM Automotive Fuse - Order by PCS Type: Fuses Fuse Tpe: Blade Selling Unit: Each Usage: Auto Car Compatibility: Universal

HQmade 30 Amp Low Profile MINI Blade Fuses – APM / ATM Automotive Fuse - Order by PCS

HQmade 30 Amp Low Profile MINI Blade Fuses – APM / ATM Automotive Fuse - Order by PCS

0.4 EUR

HQmade 30 Amp Low Profile MINI Blade Fuses – APM / ATM Automotive Fuse - Order by PCS Type: Fuses Fuse Tpe: Blade Selling Unit: Each Usage: Auto Car Compatibility: Universal

HQmade 15 Amp Low Profile MINI Blade Fuses – APM / ATM Automotive Fuse - Order by PCS

HQmade 15 Amp Low Profile MINI Blade Fuses – APM / ATM Automotive Fuse - Order by PCS

0.56 SGD

HQmade 15 Amp Low Profile MINI Blade Fuses – APM / ATM Automotive Fuse - Order by PCS Type: Fuses Fuse Tpe: Blade Selling Unit: Each Usage: Auto Car Compatibility: Universal

Solorailrade; Straight Line Connector

Solorailrade; Straight Line Connector

17.9 USD

Connects two sections or rail with electrical continuity. Allows for seamless connection of rail sections. Available in Chrome, Brushed Nickel and Dark Bronze finishes.

Zonyx Cross Connector

Zonyx Cross Connector

244.5 USD

The Zonyx Cross Connector can be used for rigid conductive connection of Zonyx tracks. Technical Specifications: 2400VA 120VAC input Suitable for dry locations only.

Qualfast M6X18Mm Studding Connector Bzp

Qualfast M6X18Mm Studding Connector Bzp

0.14 GBP

Studding connectors or coupling nuts are for connecting multiple lengths of threaded rod. Made from low carbon steel, bright zinc- plated. Manufactured to DIN 6334.

Rutland Clamp-On Tap Connector

Rutland Clamp-On Tap Connector

5.05 GBP

This male snap action tap connector has a flexible coupler on the other end which fits most taps and is then tightened onto the tap by twisting the butterfly screw.

Zonyx T Connector

Zonyx T Connector

202.5 USD

The Zonyx "T" Connector can be used for rigid conductive connection of Zonyx tracks. Technical Specifications: 2400VA 120VAC input Suitable for dry locations only.

V/A Track Connector 135v

V/A Track Connector 135v

108.0 USD

Conductive 135eg; angled connector for V/A tracks. Plugs into the ends of two track segments to create a continuously smooth track run along a vertical plane.

Zonyx Isolating Track Connector

Zonyx Isolating Track Connector

34.5 USD

The Zonyx ISO Track Connector can be used for in-line, rigid non-conductive connection of two Zonyx track when separate circuits for a single run is desired.