The Fluke 113 Digital Multimeter gives users the means to quickly and easily do basic meter set and reconnect testing. This meter is simple-to-use and has the features needed to repair most electrical problems. Using the Fluke VCHEK LoZ low impedance measurement function, users can simultaneously test for voltage or continuity. The Min/Max function lets you record signal fluctuations. The Fluke 113 can perform diode tests, and also provides both auto and manual ranging capabilities. With features such as conformance to the latest safety standards, backlight, and a much larger display that's easier to view, this meter is a must have for every toolbox.Voltage: Range: 6V to 600VResolution : 0.001V to 0.1VAccuracy: DC, 45 to 500 Hz:2.0 % + 3500 Hz to 1 kHz: 4.0 % + 3Diode test 4 Range 2.000 VResolution 0.001 VAccuracy 2.0 % + 3Continuity4 Accuracy Beeper on < 20 Î©, off > 250 Î©; detects opens or shorts of 500 Î¼s or longerâ„¦4 Range600.0 Î©6.000 kÎ©60.00 kÎ©Resolution 0.1 Î©0.001 kÎ©0.01 kÎ©Accuracy 0.9 % + 20.9 % + 10.9 % + 1Capacitance4 Range: 1000 nF to 9999 Î¼FResolution: 1 nF to 1 Î¼FAccuracy:1.9 % + 2100 Î¼F - 1000 Î¼F: 1.9 % + 2> 1000 Î¼F: 5 % + 20Notes:1 All VChek voltage ranges are specified from 60 counts to 100 % of range. Because inputs below 60 counts are not specified, it is possible and normal for this and other True-RMS meters to display non-zero readings when the test leads are disconnected from a circuit or are shorted together.2 Crest factor of â‰¤ 3 at 4000 counts, decreasing linearly to 1.5 at full scale.3 Minimum measureable input in VCHEK autorange is 3 V dc. For measurements below 3 V dc, push Range button twice to get to 6 V dc manual range.4 After measuring voltage, a wait time of 1 minute is required to maintain accuracy of ohms, capacitance, diode test, and continuity.
Ideal for electrical troubleshooting & straightforward maintenance, initial start-up testing & R&D in industry. The digital multimeter with its USB interface for the PC is capable of testing the following; - Electrical testing. - Temperature testing (K Type) from -5Â°C to 1000Â°C. AC voltage up to 700V. DC voltage up to 1000V. AC/DC current up to 10A. Resistance up to 60MW. Capacitance up to 300mF. Frequency/Duty cycle from 1Hz to 1MHz. Diode testing & buzzer. Relative measurement function. Clear display with LED back light & data hold function. Auto power off & low power indicator. Auto/manual range. Electronic protection system. Digital display count up to 6000. Conforms to IEC 1010, CAT II 1000V & CAT III 600V. Pack includes: - Digital Multimeter - Test probes - Temperature sensor - Clamp-on test lead - USB Interface - CD ROM 'PC-LINK' software (Compatible with Windows 2000, NT or XP) - 9V battery (installed) - Instruction manual PC-LINK software features: - Measure graph - Measure data record - Simulate LCD display - Analogue dial plate display - Measure Max/Min display - Sampling interval - Graph export - Measure data save Dimensions: 165(W) x 65(D) x 230(H) mm 182g Gross Weight
Fluke 1507/1503 Insulation Resistance TestersSave both time and money with automatic calculation of polarisation index and dielectric absorption ratio (only available on the1507). Make repetitive tests simple and easy with the 1507's compare (pass/fail) function (only available on the 1507). Repetitive or hard-to-reach testing is easy with the remote test probe. Live circuit detection prevents insulation test if voltage > 30V is detected for added user protection. Auto-discharge of capacitive voltage for added user protection. AC/DC voltage: 0.1 V to 600V. 200mA continuity. Features:Insulation test range:1507: 0.01 MW to 10 GW1503: 0.1 MW to 2000 MWInsulation test voltages:1507: 50V, 100V, 250V, 500V, 1000V1503: 500V, 1000VResistance: 0.01W to 20.00 kW.Save battery power with auto power off. Read measurements easily with large, backlit display. CAT IV 600V over-voltage category rating for added user protection. Remote probe, test leads, probes and alligator clips included with each tester. Accepts optional Fluke *TPAK magnetic hanging system to free your hands for other work. Four AA alkaline batteries (NEDA 15 A or IEC LR6) for at least 1000 insulation tests.
Ideal for electrical and electronic engineers. Automatic range and over range indication. Ten position rotary switch. Large, 25mm digital display with backlight. Measures DC voltage, AC voltage, resistance, capacitance, frequency, other functions include auto and manual range modes, relative measurement, data hold, diode test, continuity test and duty cycle test function Supplied with 9V battery protective cover and stand, test probes operators' manual and deluxe fitted nylon case. Complies with IEC1010 for measurement on 600V Cat III installations.Display: 3999 COUNTS. 25mm High digital display. DC Voltage: 400m/4/40/400V/-0.7%, 1000V/-0.8% AC Voltage: 4/40/400V/-0.8%, 750V/-1.0% (40Hz to 400Hz) DC Current: 4000 mu /400ma/-1.2%, 10A/-2.0% AC Current: 4000 mu /400ma/-1.5%, 10A/-3.0% (50Hz to 400Hz)Resistance: 400/4K/40K/400K/4M?/-1.2%, 40M?/-2.0%Capacitance: 4nf/-5.0%, 40n/400n/4 mu /40 mu /200 mu F/-3.0%Frequency:10/100/1000/10K/100K/1000K/10mhz/-2.0% Duty cycle: 0.1%99.9%/-2.0% Diode test autorange and manual range relative measurement data hold back light Power: 6F22(9V) x 1 Size: 185 x 84 x 38mm Weight: 285g (including battery)
Designed with on-the-job needs in mind, Fluke 62 MAX and 62 MAX+ infrared thermometers are everything you'd expect from the experts in measurement tools. Small in size, extremely accurate and very easy to use. IP54 rated for dust and water resistance.Specifications:Temperature Range: -30 Â°C to 500 Â°C (-22 Â°F to 932 Â°F) Accuracy: Â±1.5 Â°C or Â±1.5% of reading, whichever is greater -10 Â°C to 0 Â°C: Â±2.0 -30 Â°C to -10 Â°C: Â±3.0 Response Time: <500 ms (95% of reading) Spectral Response: 8 to 14 microns Emissivity 0.10 to 1.00 Optical Resolution: 10:1 (calculated at 90% energy) Repeatability of Readings: Â±0.8% of reading or <Â±1.0 Â°C (2 Â°F), whichever is greater Battery: AA x1Battery Life: 10 hours with laser and backlight on Physical Specifications:Weight: 255g Size: 175 x 85 x 75mm Operating Temperature: 0Â°C to 50Â°C (32Â°F to 122Â°F) IP Rating: IP 4 per IEC 60529 EMC: EN 61326-1:2006 EN 61326-2:2006 Compliance: EN/IEC 61010-1: 2001 Laser Safety: FDA and EN 60825-1 Class II
The new Fluke 373 clamp meters offers improved performance perfect for many AC only current measurement situations. With true-RMS AC voltage and current measurements, the Fluke 373 reads up to 600A AC and 600V AC or DC.Fluke model number: 373Application: Industrial/Residential/CommercialCable size jaw (& cable size iFlex): 32 mmi-flex flexible current probe included: n/aTrue RMS: YESAC Current (clamp) to: 600AAC Current (i-flex) to: n/aDC Current (clamp) to: n/aAC Voltage to: 600VDC Voltage to: 600VResistance & Continuity: YESFrequency to 400Hz: n/aTemperature measurement -10Â°C to + 400Â°C: n/aMotor Start-up (inrush current) capture: n/aDetachable jaw clamp & torch: n/aLow pass filter for noisy environments: n/aRemovable display operates up to 10 metres: n/amV range compatible with other accs: n/aMin/Max logging: n/aDisplay backlight: YESDisplay Hold: YESWarranty (years): 3Safety rating: CAT III 600 V, Cat IV 300 V Note : Cat IV is a higher safety rating
Ideal for electrical troubleshooting & straightforward environmental testing in residential & commercial environments. The 5-in-1 digital multimeter is capable of testing the following; - Electrical testing. - Temperature from -20Â° to 1000Â°C. - Humidity from 30 to 90%. - Sound level from 35 to 100db. - Illumination from 4000 to 40000 Lux. AC/DC voltage up to 600V. AC/DC current up to 10A. Resistance up to 40MW. Capacitance up to 200mF. Frequency from 1Hz to 200KHz. Relative measurement function. Diode testing facility. Clear display with LED back light & data hold function. Auto power OFF & low power indicator. Digital display count up to 3999. Conforms to IEC 1010, CAT II 1000V and CAT III 600V. Pack includes: - Environment digital multimeter - Test probes - Clamp-on test leads - Temperature sensor probe - 9V battery (installed) - Instruction manual Product Dimensions: 165(W) x 65(D) x 230(H) mm 618g Gross Weight
Fluke Networks 10051501 D914 Impact Tool with EverSharp 110, EverSharp 66 Blade & Free Blade Specifications: The versatile D914â„¢ series impact tools include built-in probe pic/spudger and torque capability. Industry standard, internationally accepted Hook and spudger tools are built into the handle Automatic spring handle --choose low impact for 24/26 gauge wire or high impact for 22-gauge wire D914 and D914S impact tools accept Phillips-head or flat screwdriver blade Convenient blade storage built into the handle Adapter blade allows technician to use a variety of torque tool bits and sockets Easy blade insertion, locks in place D914STM soft touch impact tool features a rubber handle and special ergonomic design for better grip and to reduce hand fatigue Package Contents: D914 Impact Tool EverSharp 110 Blade EverSharp 66 Blade Blade Parts: 1 year limited
Ideal for electrical and electronic engineers. Automatic range and over range indication. Ten position rotary switch. Large, 25mm digital display with backlight. Measures current DC voltage, AC voltage, resistance, capacitance, frequency, other features include, relative measurement, data hold, diode test, continuity test and duty cycle test function. Supplied with 9V battery protective cover and stand, test probes operators' manual and deluxe fitted nylon case. Complies with IEC1010 for measurement up to 600V Cat III installations (and 1000V Cat II)DISPLAY: 3999 Counts.DCV: 4/40/400V /- 0.7% 1000V /- 0.8%ACV: 4/40/400V /- 0.8% 700V /- 1.0%ACA: 200A /- 3.0% (50Hz to 1000Hz)Ohm: 400/4k/40k/4M Ohm/- 1.2% 40M Ohm/-2.0%CAP: 40n/400n/4 mu /40 mu F /- 4.0%FREQUENCY: 10Hz to 100Khz /- 2.0%DUTY CYCLE: 0.1% to 99.9%BACKLIGHT AUTO OFF TIME LIMIT MODE
Temperature and humidity are two important factors in maintaining optimal comfort levels and good indoor air quality. Quickly and conveniently take accurate humidity and temperature readings with the 971. Invaluable for facility maintenance and utility technicians, HVAC-service contractors, and specialists who assess indoor air quality (IAQ). Specification:Temperature: -20Â°C to 60Â°C (-4Â°F to 140Â°F)Temperature accuracy 0Â°C to 45Â°C (Â±0.5Â°C) -20Â°C to 0Â°C & 45Â°C to 60Â°C (Â±1.0Â°C)32Â°F to 113Â°F (Â±1.0Â°F)-4Â°F to 32Â°F & 113Â°F to 140Â°F (Â±2.0Â°F)Resolution: 0.1Â°C / 0.1Â°FTemperature Update Rate: 500 msTemperature Sensor Type: NTCRelative Humidity Range: 5% to 95% RHRelative Humidity Accuracy 10% to 90%RH @ 23 Â°C (73.4Â°F) (Â±2.5%RH)(<10%, > 90%RH @23Â°C (73.4Â°F) (Â±5.0%RH)
Fluke Networks MS2-KIT MicroScanner2 Professional Kit Specifications: Includes Accessories: MicroScanner2 Cable Verifier main wiremap adapter remote identifiers #2-7 IntelliTone Pro 200 probe shielded twisted-pair RJ45 patch cord RJ11 patch cord clip-set RJ45 to 8 alligator clip bare wire adapter F Coax push on patch cord accessory soft pouch (2) AA alkaline batteries (1) 9V alkaline battery MicroScanner2 Getting Started Guide MicroScanner2 Owners CD IntelliTone Pro Getting Started Guide MicroScanner2 owners CD IntelliTone Pro Getting Started Guide IntelliTone Pro owners CD packaged in a deluxe Fluke Networks carry case Package Contents: 78526N Parts: 1 year limited Electrical Outlet Plug Type: others
Wireless K-Type thermocouple bead probe for stand-alone use or with the Fluke Connect system. Connect a t3000 to quickly spot temperature differences from a safe distance. Use it with FC current and voltage meters to view all parameters at the same time or log measurements over time to identify trends. Upload saved data to your PC or mobile device. Logs up to 65,000 readings. Supplied with a magnetic hanging strap. Relays measurements wirelessly to the Fluke 3000 FC DMM, Ti200/300/400 infrared cameras, and mobile devices.Temperature measurements: -200Â°C - 1372Â°CTemperature Scale CentigradeBattery Type AABest Accuracy Â±0.5% + 0.3 Â°CProbe Type KResolution 0.1 Â°CWeight 220g
Fluke Networks Pro3000 Analog Tone Generator Specifications: User interface Slide switch selects Continuity or Tone Mode Push button switch selects SOLID, ALT or OFF Tone mode LED Continuity/Polarity LED Solid Frequency 1000 Hz nominal Alternating Frequency 1000/1500 Hz nominal Over Voltage Protection 60 Vdc in Toner/Polarity Mode Output Power in Tone Mode 8 dbm into 600 ohms Output Voltage Level in Continuity Mode 8 Vdc with fresh battery Battery 9V alkaline Temperature Operating: -20Â° C to 60Â° C, Storage: -40Â° C to 70Â° C Case dimensions 2.7 in. x 2.4 in. x 1.4 in. (6.9 cm x 6.1 cm x 3.6 cm) Parts: 18 Month
This is the industry standard, with all the features you need to troubleshoot and repair so many problems in electrical and electronic systems.Fluke 177 Series digital multimeter give you True RMS voltage and current measurements, 6000-count resolution, manual and automatic ranging and provide frequency, capacitance, resistance, continuity and diode measurements. In addition, provide higher 0.09% basic accuracy, a digital display with analogue bar graph and backlit.Voltage DC: 0.1mV - 1000VVoltage AC: 0.1mV - 1000VCurrent DC: 0.01mA - 10A Current AC: 0.01mA - 10AResistance: 0.1 - 50M OhmsCapacitance: 1nF - 100kHzFrequency: 0.01Hz - 100kHzTemperature: 0.1Â°C -40/400Â°C
2ACDesigned to be pocket-sized and easy to use. The 2AC tests for energised circuits and defective grounds. The tip of the pocket-sized tester will glow red when within close proximity of an outlet, terminal strip, or power cord where voltage is present. Voltage detection from 200 to 1000V AC, suitable for a wide range of residential, commercial and industrial needs. Always on, using special low power circuitry to sustain battery life and ensure your 2AC is always ready. Category IV - 1000V over-voltage rated product for best in class user protection. Integrated clip design, optimised for pocket storage. Powered by 2x AAA batteries (included). Two-year warranty.
FunctionsVoltage, current and resistance measurementCapacitance and frequency measurementDiode and acoustic continuity testTemperature measurementProduct informationAutomatic and manual range selectionIntegrated measurement memory (data hold)MIN/MAX, relative and peak value measurementAdditional bar graph display (41 segments)BacklightShock-proof and impact-resistant thanks to standard protective holsterAuto power-offProduct highlightsTrue RMS measurement (TRMS)Magnetic holster (Magne-Grip)Duty cycle functionMeasurement Range:Voltage: AC 400mV - 750VDC 400mV - 1000VCurrent: AC/DC 400ÂµA -10AResistance: 40MÎ©Capacitance: 4000ÂµFTemperature: -20Â°C to 1000Â°C.
The 561 IR and contact thermometer, combines the temperature measurement functions that industrial, electrical, and HVAC/R professionals need, all in one tool. It measures both infrared and contact temperature, replacing several other test tools. It's fast, efficient, and easy to use, saving you valuable time and effort.Temperature Range: -40 to 550 Â°C (-40 to 1022 Â° F) Accuracy: Â±1.0 % of reading Â±1 % of reading or Â±1 Â°C (Â±2 Â°F), whichever is greater below 0 Â°C/32 Â°F, Â±1 Â°C (Â±2 Â°F) Â± 0.1Â°/1Â°D/S ratio: 12:1Emissivity: Adjustable with three settings Low (0.3), Medium (0.7). High (0.95)Power Source: 2 AA batteries (alkaline or NiCD)
The DM383 Digital Multimeter from Edison is a compact unit that has a removable rubber protective holder, that protects it against the bumps and knocks encountered on site.Features include:Continuity testing.Transistor hFE.Reading/peak hold.Fused current range.Auto power off.Overload indication.Low battery indication.Tilt stand/hanger.DM383 specificationVoltage max: 600V AC/600V DC. Current max: 10A DC. Resistance max: 2M Ohms. Safety rating: Cat II. Supplied complete with: 9V battery.1 year warranty.Supplied with holster.For the full range of Edison multimeters please refer to the catalogue PDF or enter the search EDI-516.
PRV240The Fluke PRV240 proving unit is a portable, pocket-sized, battery-powered voltage source. It is unique in that it sources stable AC and DC voltages for both LoZ and HiZ instruments. The PRV240 reduces the risk of shock and arc flash by removing unnecessary exposure to a potentially hazardous electrical environment while verifying the functionality of test tools before and after absence or presence of voltage is checked.Output voltage: 240V AC RMS or DC (Â±10% â‰¥1MÎ©). LoZ>3kÎ© load (60V AC typical, 50V AC RMS minimum).Operating temperature: -10Â°C to +50Â°C.Safety: IEC61010-1, IEC61010-2-030.
77-IVThe 77-IV has the features needed to repair most electrical and electronic problems. A large display and backlight assists work in dim areas. Minimum/Maximum to record signal fluctuations. Ergonomic overmolded housing with integrated probe holders. Auto and manual ranging and it meets Measurement Category 1000 It measures: Wide 1000 V measurement range Average responding AC measurements 0.3% accuracy 10 Amps continuous (20A for 30 seconds) Frequency and capacitance Resistance and continuity Measurement Category IV safety rating
Test leads are an integral part of the complete measurement system and extend the capabilities of your digital multimeter. The TL224 SureGrip Insulated Test leads offer reinforced strain relief and includes banana jack termination for a variety of test lead configurations. SureGrip accessories are designed to improve steadiness in slippery hands. Rubber over molded surfaces and finger-hugging curves give the user a comfortable, reliable grip on the accessory so they can focus on making an accurate measurement.
DM664 Digital Multimeter specification: Extra large digits, temperature probe and short lead capacitor, removable rubber holster with lead holders. Continuity, diode, transistor hFE, auto power off, overload indication, low battery indicator, tilt stand/hanger.Voltage (max): 700V AC 1000V DC. Current (max): 10A AC/DC. Resistance (max): 200MW.Capacitance (max): 200mF.Frequency (max): 20kHz.Temperature (max): -20 to 1000C. Safety Rating: Cat III 600V. Cat II 1000V. 1 year warranty.Supplied with holster.
DAM668 Digital Multimeter Features include:Continuity, diode, transistor hFE, auto ranging, reading/peak hold, bar graph, fused current range, overload indication: low battery indicator, tilt stand/hanger. Voltage max: 700V AC 1000V DC.Current max: 10A AC/DC. Resistance max: 32.6MW. Capacitance max: 32.6mF. Frequency max: 150kHz. Safety Rating; Cat III 600V, Cat II 1000V. Warranty: 1 year. Supplied with removable rubber holster with integral lead holders.
179 True RMS Voltage & Current Measurements Multimeter0.09% basic accuracy, 6000 count resolution. Display hold and auto hold. Frequency and capacitance measurements. Resistance, continuity and diode measurements. Temperature measurements. Min-max-average recording. EN61010-1 Cat III 1000V/Cat IV 600V.Measures twice as fast as other multimeters.Accessories: 80BK temperature probe. Installed 9V battery. Test leads. Users manual.
Killzone Servitude T-Shirt This is an officially licensed Killzone t-shirt in which these Killzone shirts have been screen printed with the Killzone image on front. These Killzone tshirts are usually made from heavyweight preshrunk 6oz. cotton tee shirt blanks. Check back often for some of our new Killzone clothing and other Killzone Merchandise at great prices only at - www.StylinOnline.com .
DM78C 5 functions/16 ranges. Continuity test: buzzer alert. Auto power off saves batteries. Data Hold. Protective case includedDisplay: LCD, 3-3/4-digit, 3400 Count. Mesaurement ranges: Voltage: AC 0.001V - 600V (50 ~ 60Hz). Voltage: DC 0.1mV - 600V. Input impedance: 10MW. Resistance: 0.1W - 34MW. Continuity R: <340W. Dimensions: 130 x 77 x 18mm. Weight: approx. 110g (incl. battery and case).
116Compact true-rms meter for HVAC troubleshooting. It has everything needed in an HVAC meter including temperature and microamp measurements to quickly troubleshoot problems with HVAC equipment and flame sensors.Voltage max: 600V AC/DC. Current max: 600mA AC/DC. Capacitance max: 500mF. Temp. range: -40Â°C - 400Â°C. Continuity: 600W. Diode test: 2V. Safety rating: Cat III 600V.
Features backlit LED ladder, voltage & polarity, single pole test for phase detection, audible & visual continuity test, rotary field indicator, switchable load (30mA with buttons pressed), vibrates under load, torch, digital backlit display with display hold, resistance measurement to 2k Ohm.Voltage AC/DC: 6V - 690VIP Rating: IP65Safety Certification: CATIV 600V, CATIII 690V
424DMeasure distance up to 100m single handed. 180Âº inclination sensor for levelling & height tracking and a built in compass to determine the 'heading'. Automatic end-piece correction for fast & accurate measurements from internal & external corners. Automatic end-piece correction. Stake out & Pythagoras functions. line backlit LCD display. 20 reading memory.
15XP-BVoltage, current and resistance measurement. Diode and acoustic continuity test. Logic test function (TTL). Automatic and manual range selection. Integrated measurement memory (data hold). Shock-proof and impact-resistant thanks to standard protective holster. Auto power-off. Non-contact voltage detection (NCV). Magnetic holster (Magne-Grip).
Handcrafted unstructured suede tote in black. Carry handle at top. Partially exposed bag interior featuring logo stamp in silver-tone, zippered pocket, and tonal leather lining. Magnetic fastening at bag throat. Patch pockets at interior. Leather lining in navy. Silver-tone hardware. Tonal stitching. Approx. 15 length x 15.5 height x 4 width.
Easy and accurate OpenJaw current measurementContinuity beeperCompact design with neat probe storageAuto off mode to conserve battery lifeAC Voltage: 100VDC voltage: 1000VAC./DC current 100AResistance: 1000WCalibration Frequency:45 to 66 HzDigital Display Count 1000Safety Category: 1000V CAT IIIWeight: 300gSize: (H x W x D)230 x 51 x 30.5mm
Pocket sized with integral lead storage. Features include continuity, diode, reading/peak hold, fused current range, auto power off, overload indication, low battery indication.Voltage max: 600V AC 600V DC. Current max: 400mA AC/DC. Resistance max: 40MW. Safety rating: Cat II. 1 year warranty.Supplied with wallet.
115Used for a wide variety of electrical and electronic testing applications. This true-rms meter provides easy one handed operation in a compact package. Voltage max: 600V AC/DC. Current max: 20A DC. Capacitance max: 1000mF. Frequency max: 50kHz. Continuity: 600W. Diode test: 2V. Safety rating: Cat III 600V.
Features backlit LED ladder, voltage & polarity, single pole test for phase detection, audible & visual continuity test, rotary field indicator, switchable load (30mA with buttons pressed), vibrates under load, torch.Voltage AC/DC: 12V - 690VIP Rating: IP65Safety Certification: CATIV 600V, CATIII 690V
117Ideal for demanding settings such as commercial buildings, hospitals and schools. Includes integrated non-contact voltage detection. Voltage max: 600V AC/DC. Current max: 20A AC. Capacitance max: 1000mF. Frequency max: 50kHz. Continuity: 600W. Diode Test: 2V. Safety rating: Cat III 600V.
419DLaser accuracy to 1mm. Automatically add or subtract measurements. Measure area & volume without calculation errors. Stake out & Pythagoras functions.80m distance measurement. 3 line backlit LCD display.20 reading memory. Tripod mount. IP54 water & dust resistant. 3 year warranty.
414DMeasure distance up to 50m single handed. Laser accuracy to 2mm. Automatically add or subtract measurements. Measure area & volume without calculation errors. 2 line display. 5 reading memory.3,000 measurements. Includes protective pouch & belt lanyard.
TS-6004mm detachable probes, instruction sheet, continuity beeper, rugged enough to withstand 30m (10ft) drop. Features include continuity and auto power off.Voltage max: 600V, 600V DC.Current max: 100A.Resistance max: 1000W.Safety rating: Cat III.
Pilot ENO-G Mechanical Pencil Leads Compatible Devices These new generation leads extremely resistant, are specially adapted to PILOT mechanical pencils For optimal operation of these leads, we recommend the use of PILOT mechanical pencils
Fluke Networks SimpliFiber SFPOWERMETER Pro Optical Power Meter Specifications: Number of USB Ports:1 Number of SC Ports:1 Product Type:Network Testing Device Package Contents: SimpliFiber SFPOWERMETER Pro Optical Power Meter SC Adapter
High qualityBEC male connector.Golden plated to ensure very good contact.95mm 22 Gauge silicone wireWith pre-coated soldering for easy solderingMust have for making your customized battery packs for RC Aircraftof Micro HPI etc
Universal Test Leads - TL71-1Premium test leads. Pair of silicone insulated testleads with shrouded banana plugs and test probes with protective caps. Recommended for Î¼V measurements.IEC 61010 : Cat III 1000 V / Cat IV 600 V
Fluke Networks 11292000 Pro-Tool IS50 Kit Specifications: Product Name: Pro-Tool Kit Product Type: Hardware Connectivity Kit Package Contents: IS50 with D914S Impact Tool D-Snips Cable Stripper EverSharp 66/110 cut blade
Vichy VC99 3 6/7 Digital Multimeter analog bar C F better FLUKE 17B Size/Dimensions: 185x93x35mm Analog/Digital: Digital Includes: 1 x User Manual 1X VC99 1X Red Probe 1X Black Probe 1X Thermal Couple TK cable
Features backlit LED ladder, voltage & polarity, single pole test for phase detection, audible & visual continuity test.Voltage AC/DC: 12V - 690VIP Rating: IP54Safety Certification: CATIII 600V, CATII 690V
Fluke Networks 11291000 Networks IS40 ProTool Kit Package Contents: D814 Impact Tool Electricians D-Snips Cable Stripper EverSharp 66 / 110 Cut Blade Probe Pic Carrying case Parts: 1 year limited
114Used for troubleshooting on 'go/no-go' testing. It includes a feature to prevent false readings caused by ghost voltage.Voltage max: 600V AC/DC. Continuity: 600W. Safety rating: Cat III 600V.
These pencil leads are 2 mm. in diameter and are of artist quality. They come in plastic, stoppered carrying tubes, with two leads per tube.Pacific Arc 2 mm pencil leads are 5 in. long.
Pair of silicone insulated testleads with shrouded banana plugs and test probes with removeable lantern tips and GS38 probetip covers.IEC 61010 : Cat III 1000 V / Cat IV 600 V