Vidgrids » leapfrog 3d printer

leapfrog 3d printer

Premium 3D Printer Filament ABS 1.75MM 1kg/spool, Bright Orange

Premium 3D Printer Filament ABS 1.75MM 1kg/spool, Bright Orange

54.99 USD

Premium 3D Printer Filament ABS 1.75MM 1kg/spool, Bright Orange Compatible Devices Premium 3D Printer Filament ABS 1.75MM 1kg/spool, Bright Orange Get outstanding 3D printing results when you use 1.75mm ABS 3D Printer Filament from 123inkcartridges! ABS is one of the most commonly used filament types in 3D printing. It has a high tensile strength and good overall toughness. It has a low density and is softer than PLA, which means lower weight and lower cost when printing large models. Hardness is such that no white dot appears when bending. This 1 Kg spool features a thickness of 1.75mm ±0.10mm, with a roundness variation of only 0.05mm. It has a nominal processing temperature of 230° C (446°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. The negatives of using ABS is that it can give off a white smoke with a concentrated odor. It is best to ensure that the printing room is well ventilated when using ABS. Additionally, it has a high moisture absorption rate. Depending on the overall humidity level of the printing environment, an opened spool can absorb enough moisture after a couple of days that high temperature printing could cause bubbles or pocks in the extrusion. It is therefore recommended to not open a spool until you are ready to print and to store any unused portion with with silca gel and/or an active dehumidifier to reduce the amount of moisture it can absorb. Reel Dimensions: Reel Diameter: 195mm (7.68") Hub Diameter: 95mm (3.74") Spindle Diameter: 38mm (1.50") Reel Width: 80mm (3.15")

Premium 3D Printer Filament ABS 3MM 1kg/spool, White

Premium 3D Printer Filament ABS 3MM 1kg/spool, White

54.99 USD

Premium 3D Printer Filament ABS 3MM 1kg/spool, White Compatible Devices Premium 3D Printer Filament ABS 3MM 1kg/spool, White Get outstanding 3D printing results when you use 3.0mm ABS 3D Printer Filament from 123inkcartridges! ABS is one of the most commonly used filament types in 3D printing. It has a high tensile strength and good overall toughness. It has a low density and is softer than PLA, which means lower weight and lower cost when printing large models. Hardness is such that no white dot appears when bending. This 1 Kg spool features a thickness of 3.0mm ±0.10mm, with a roundness variation of only 0.05mm. It has a nominal processing temperature of 200° C (392°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. The negatives of using ABS is that it can give off a white smoke with a concentrated odor. It is best to ensure that the printing room is well ventilated when using ABS. Additionally, it has a high moisture absorption rate. Depending on the overall humidity level of the printing environment, an opened spool can absorb enough moisture after a couple of days that high temperature printing could cause bubbles or pocks in the extrusion. It is therefore recommended to not open a spool until you are ready to print and to store any unused portion with with silca gel and/or an active dehumidifier to reduce the amount of moisture it can absorb. Reel Dimensions: Reel Diameter: 195mm (7.68") Hub Diameter: 95mm (3.74") Spindle Diameter: 38mm (1.50") Reel Width: 80mm (3.15")

Premium 3D Printer Filament ABS 3MM 1kg/spool, Black

Premium 3D Printer Filament ABS 3MM 1kg/spool, Black

54.99 USD

Premium 3D Printer Filament ABS 3MM 1kg/spool, Black Compatible Devices Premium 3D Printer Filament ABS 3MM 1kg/spool, Black Get outstanding 3D printing results when you use 3.0mm ABS 3D Printer Filament from 123inkcartridges! ABS is one of the most commonly used filament types in 3D printing. It has a high tensile strength and good overall toughness. It has a low density and is softer than PLA, which means lower weight and lower cost when printing large models. Hardness is such that no white dot appears when bending. This 1 Kg spool features a thickness of 3.0mm ±0.10mm, with a roundness variation of only 0.05mm. It has a nominal processing temperature of 200° C (392°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. The negatives of using ABS is that it can give off a white smoke with a concentrated odor. It is best to ensure that the printing room is well ventilated when using ABS. Additionally, it has a high moisture absorption rate. Depending on the overall humidity level of the printing environment, an opened spool can absorb enough moisture after a couple of days that high temperature printing could cause bubbles or pocks in the extrusion. It is therefore recommended to not open a spool until you are ready to print and to store any unused portion with with silca gel and/or an active dehumidifier to reduce the amount of moisture it can absorb. Reel Dimensions: Reel Diameter: 195mm (7.68") Hub Diameter: 95mm (3.74") Spindle Diameter: 38mm (1.50") Reel Width: 80mm (3.15")

Premium 3D Printer Filament ABS 3MM 1kg/spool, Blue

Premium 3D Printer Filament ABS 3MM 1kg/spool, Blue

54.99 USD

Premium 3D Printer Filament ABS 3MM 1kg/spool, Blue Compatible Devices Premium 3D Printer Filament ABS 3MM 1kg/spool, Blue Get outstanding 3D printing results when you use 3.0mm ABS 3D Printer Filament from 123inkcartridges! ABS is one of the most commonly used filament types in 3D printing. It has a high tensile strength and good overall toughness. It has a low density and is softer than PLA, which means lower weight and lower cost when printing large models. Hardness is such that no white dot appears when bending. This 1 Kg spool features a thickness of 3.0mm ±0.10mm, with a roundness variation of only 0.05mm. It has a nominal processing temperature of 200° C (392°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. The negatives of using ABS is that it can give off a white smoke with a concentrated odor. It is best to ensure that the printing room is well ventilated when using ABS. Additionally, it has a high moisture absorption rate. Depending on the overall humidity level of the printing environment, an opened spool can absorb enough moisture after a couple of days that high temperature printing could cause bubbles or pocks in the extrusion. It is therefore recommended to not open a spool until you are ready to print and to store any unused portion with with silca gel and/or an active dehumidifier to reduce the amount of moisture it can absorb. Reel Dimensions: Reel Diameter: 195mm (7.68") Hub Diameter: 95mm (3.74") Spindle Diameter: 38mm (1.50") Reel Width: 80mm (3.15")

Premium 3D Printer Filament ABS 3MM 1kg/spool, Red

Premium 3D Printer Filament ABS 3MM 1kg/spool, Red

54.99 USD

Premium 3D Printer Filament ABS 3MM 1kg/spool, Red Compatible Devices Premium 3D Printer Filament ABS 3MM 1kg/spool, Red Get outstanding 3D printing results when you use 3.0mm ABS 3D Printer Filament from 123inkcartridges! ABS is one of the most commonly used filament types in 3D printing. It has a high tensile strength and good overall toughness. It has a low density and is softer than PLA, which means lower weight and lower cost when printing large models. Hardness is such that no white dot appears when bending. This 1 Kg spool features a thickness of 3.0mm ±0.10mm, with a roundness variation of only 0.05mm. It has a nominal processing temperature of 200° C (392°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. The negatives of using ABS is that it can give off a white smoke with a concentrated odor. It is best to ensure that the printing room is well ventilated when using ABS. Additionally, it has a high moisture absorption rate. Depending on the overall humidity level of the printing environment, an opened spool can absorb enough moisture after a couple of days that high temperature printing could cause bubbles or pocks in the extrusion. It is therefore recommended to not open a spool until you are ready to print and to store any unused portion with with silca gel and/or an active dehumidifier to reduce the amount of moisture it can absorb. Reel Dimensions: Reel Diameter: 195mm (7.68") Hub Diameter: 95mm (3.74") Spindle Diameter: 38mm (1.50") Reel Width: 80mm (3.15")

Premium 3D Printer Filament PLA 1.75MM 1kg/spool, Fluorescent Yellow

Premium 3D Printer Filament PLA 1.75MM 1kg/spool, Fluorescent Yellow

54.99 USD

Premium 3D Printer Filament PLA 1.75MM 1kg/spool, Fluorescent Yellow Compatible Devices Premium 3D Printer Filament PLA 1.75MM 1kg/spool, Fluorescent Yellow Get outstanding 3D printing results when you use 1.75mm PLA 3D Printer Filament from 123inkcartridges! PLA is a good choice for a printing material if you are looking for high accuracy and high resolution. It extrudes at lower temperatures, does not require a heated base, and has a very low shrinkage rate (0.3%). PLA is harder than ABS, but is therefore also a bit more brittle. Additionally, PLA is a plant-based plastic, which means that it is biodegradable and gives off a slightly sweet odor, like roasting corn. This 1 Kg spool features a thickness of 1.75mm ±0.10mm, with a roundness variation of only 0.03mm. It has a nominal processing temperature of 210° C (410°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. The negatives of using PLA is that it is vulnerable to degradation from moisture, sunlight, and heat. Additionally, it is more prone to overheating during processing, which can cause dripping and drooping if it gets too hot. Reel Dimensions: Reel Diameter: 195mm (7.68") Hub Diameter: 95mm (3.74") Spindle Diameter: 38mm (1.50") Reel Width: 80mm (3.15")

Premium 3D Printer Filament PLA 1.75MM 1kg/spool, Crystal Clear

Premium 3D Printer Filament PLA 1.75MM 1kg/spool, Crystal Clear

54.99 USD

Premium 3D Printer Filament PLA 1.75MM 1kg/spool, Crystal Clear Compatible Devices Premium 3D Printer Filament PLA 1.75MM 1kg/spool, Crystal Clear Get outstanding 3D printing results when you use 1.75mm PLA 3D Printer Filament from 123inkcartridges! PLA is a good choice for a printing material if you are looking for high accuracy and high resolution. It extrudes at lower temperatures, does not require a heated base, and has a very low shrinkage rate (0.3%). PLA is harder than ABS, but is therefore also a bit more brittle. Additionally, PLA is a plant-based plastic, which means that it is biodegradable and gives off a slightly sweet odor, like roasting corn. This 1 Kg spool features a thickness of 1.75mm ±0.10mm, with a roundness variation of only 0.03mm. It has a nominal processing temperature of 210° C (410°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. The negatives of using PLA is that it is vulnerable to degradation from moisture, sunlight, and heat. Additionally, it is more prone to overheating during processing, which can cause dripping and drooping if it gets too hot. Reel Dimensions: Reel Diameter: 195mm (7.68") Hub Diameter: 95mm (3.74") Spindle Diameter: 38mm (1.50") Reel Width: 80mm (3.15")

Premium 3D Printer Filament PLA 1.75MM 1kg/spool, Bright Green

Premium 3D Printer Filament PLA 1.75MM 1kg/spool, Bright Green

54.99 USD

Premium 3D Printer Filament PLA 1.75MM 1kg/spool, Bright Green Compatible Devices Premium 3D Printer Filament PLA 1.75MM 1kg/spool, Bright Green Get outstanding 3D printing results when you use 1.75mm PLA 3D Printer Filament from 123inkcartridges! PLA is a good choice for a printing material if you are looking for high accuracy and high resolution. It extrudes at lower temperatures, does not require a heated base, and has a very low shrinkage rate (0.3%). PLA is harder than ABS, but is therefore also a bit more brittle. Additionally, PLA is a plant-based plastic, which means that it is biodegradable and gives off a slightly sweet odor, like roasting corn. This 1 Kg spool features a thickness of 1.75mm ±0.10mm, with a roundness variation of only 0.03mm. It has a nominal processing temperature of 210° C (410°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. The negatives of using PLA is that it is vulnerable to degradation from moisture, sunlight, and heat. Additionally, it is more prone to overheating during processing, which can cause dripping and drooping if it gets too hot. Reel Dimensions: Reel Diameter: 195mm (7.68") Hub Diameter: 95mm (3.74") Spindle Diameter: 38mm (1.50") Reel Width: 80mm (3.15")

Premium 3D Printer Filament PLA 1.75MM 1kg/spool, Black

Premium 3D Printer Filament PLA 1.75MM 1kg/spool, Black

54.99 USD

Premium 3D Printer Filament PLA 1.75MM 1kg/spool, Black Compatible Devices Premium 3D Printer Filament PLA 1.75MM 1kg/spool, Black Get outstanding 3D printing results when you use 1.75mm PLA 3D Printer Filament from 123inkcartridges.ca! PLA is a good choice for a printing material if you are looking for high accuracy and high resolution. It extrudes at lower temperatures, does not require a heated base, and has a very low shrinkage rate (0.3%). PLA is harder than ABS, but is therefore also a bit more brittle. Additionally, PLA is a plant-based plastic, which means that it is biodegradable and gives off a slightly sweet odor, like roasting corn. This 1 Kg spool features a thickness of 1.75mm ±0.10mm, with a roundness variation of only 0.03mm. It has a nominal processing temperature of 210° C (410°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. The negatives of using PLA is that it is vulnerable to degradation from moisture, sunlight, and heat. Additionally, it is more prone to overheating during processing, which can cause dripping and drooping if it gets too hot. Reel Dimensions: Reel Diameter: 195mm (7.68") Hub Diameter: 95mm (3.74") Spindle Diameter: 38mm (1.50") Reel Width: 80mm (3.15")

Premium 3D Printer Filament PLA 1.75MM 1kg/spool, Blue

Premium 3D Printer Filament PLA 1.75MM 1kg/spool, Blue

35.99 USD

Premium 3D Printer Filament PLA 1.75MM 1kg/spool, Blue Compatible Devices Premium 3D Printer Filament PLA 1.75MM 1kg/spool, Blue Get outstanding 3D printing results when you use 1.75mm PLA 3D Printer Filament from 123inkcartridges.ca! PLA is a good choice for a printing material if you are looking for high accuracy and high resolution. It extrudes at lower temperatures, does not require a heated base, and has a very low shrinkage rate (0.3%). PLA is harder than ABS, but is therefore also a bit more brittle. Additionally, PLA is a plant-based plastic, which means that it is biodegradable and gives off a slightly sweet odor, like roasting corn. This 1 Kg spool features a thickness of 1.75mm ±0.10mm, with a roundness variation of only 0.03mm. It has a nominal processing temperature of 210° C (410°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. The negatives of using PLA is that it is vulnerable to degradation from moisture, sunlight, and heat. Additionally, it is more prone to overheating during processing, which can cause dripping and drooping if it gets too hot. Reel Dimensions: Reel Diameter: 195mm (7.68") Hub Diameter: 95mm (3.74") Spindle Diameter: 38mm (1.50") Reel Width: 80mm (3.15")

Premium 3D Printer Filament PLA 1.75MM 1kg/spool, Red

Premium 3D Printer Filament PLA 1.75MM 1kg/spool, Red

54.99 USD

Premium 3D Printer Filament PLA 1.75MM 1kg/spool, Red Compatible Devices Premium 3D Printer Filament PLA 1.75MM 1kg/spool, Red Get outstanding 3D printing results when you use 1.75mm PLA 3D Printer Filament from 123inkcartridges! PLA is a good choice for a printing material if you are looking for high accuracy and high resolution. It extrudes at lower temperatures, does not require a heated base, and has a very low shrinkage rate (0.3%). PLA is harder than ABS, but is therefore also a bit more brittle. Additionally, PLA is a plant-based plastic, which means that it is biodegradable and gives off a slightly sweet odor, like roasting corn. This 1 Kg spool features a thickness of 1.75mm ±0.10mm, with a roundness variation of only 0.03mm. It has a nominal processing temperature of 210° C (410°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. The negatives of using PLA is that it is vulnerable to degradation from moisture, sunlight, and heat. Additionally, it is more prone to overheating during processing, which can cause dripping and drooping if it gets too hot. Reel Dimensions: Reel Diameter: 195mm (7.68") Hub Diameter: 95mm (3.74") Spindle Diameter: 38mm (1.50") Reel Width: 80mm (3.15")

Premium 3D Printer Filament PLA 3MM 1kg/spool, White

Premium 3D Printer Filament PLA 3MM 1kg/spool, White

54.99 USD

Premium 3D Printer Filament PLA 3MM 1kg/spool, White Compatible Devices Premium 3D Printer Filament PLA 3MM 1kg/spool, White Get outstanding 3D printing results when you use 3.0mm PLA 3D Printer Filament from 123inkcartridges! PLA is a good choice for a printing material if you are looking for high accuracy and high resolution. It extrudes at lower temperatures, does not require a heated base, and has a very low shrinkage rate (0.3%). PLA is harder than ABS, but is therefore also a bit more brittle. Additionally, PLA is a plant-based plastic, which means that it is biodegradable and gives off a slightly sweet odor, like roasting corn. This 1 Kg spool features a thickness of 3.0mm ±0.10mm, with a roundness variation of only 0.03mm. It has a nominal processing temperature of 185° C (365°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. The negatives of using PLA is that it is vulnerable to degradation from moisture, sunlight, and heat. Additionally, it is more prone to overheating during processing, which can cause dripping and drooping if it gets too hot.   Reel Dimensions: Reel Diameter: 195mm (7.68") Hub Diameter: 95mm (3.74") Spindle Diameter: 38mm (1.50") Reel Width: 80mm (3.15")

Premium 3D Printer Filament PLA 1.75MM 1kg/spool, White

Premium 3D Printer Filament PLA 1.75MM 1kg/spool, White

47.99 USD

Premium 3D Printer Filament PLA 1.75MM 1kg/spool, White Compatible Devices Premium 3D Printer Filament PLA 1.75MM 1kg/spool, White Get outstanding 3D printing results when you use 1.75mm PLA 3D Printer Filament from Monoprice! PLA is a good choice for a printing material if you are looking for high accuracy and high resolution. It extrudes at lower temperatures, does not require a heated base, and has a very low shrinkage rate (0.3%). PLA is harder than ABS, but is therefore also a bit more brittle. Additionally, PLA is a plant-based plastic, which means that it is biodegradable and gives off a slightly sweet odor, like roasting corn. This 1 Kg spool features a thickness of 1.75mm ±0.10mm, with a roundness variation of only 0.03mm. It has a nominal processing temperature of 210° C (410°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. The negatives of using PLA is that it is vulnerable to degradation from moisture, sunlight, and heat. Additionally, it is more prone to overheating during processing, which can cause dripping and drooping if it gets too hot. Reel Dimensions: Reel Diameter: 195mm (7.68") Hub Diameter: 95mm (3.74") Spindle Diameter: 38mm (1.50") Reel Width: 80mm (3.15")

Premium 3D Printer Filament PLA 3MM 1kg/spool, Black

Premium 3D Printer Filament PLA 3MM 1kg/spool, Black

54.99 USD

Premium 3D Printer Filament PLA 3MM 1kg/spool, Black Compatible Devices Premium 3D Printer Filament PLA 3MM 1kg/spool, Black Get outstanding 3D printing results when you use 3.0mm PLA 3D Printer Filament from 123inkcartridges! PLA is a good choice for a printing material if you are looking for high accuracy and high resolution. It extrudes at lower temperatures, does not require a heated base, and has a very low shrinkage rate (0.3%). PLA is harder than ABS, but is therefore also a bit more brittle. Additionally, PLA is a plant-based plastic, which means that it is biodegradable and gives off a slightly sweet odor, like roasting corn. This 1 Kg spool features a thickness of 3.0mm ±0.10mm, with a roundness variation of only 0.03mm. It has a nominal processing temperature of 185° C (365°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. The negatives of using PLA is that it is vulnerable to degradation from moisture, sunlight, and heat. Additionally, it is more prone to overheating during processing, which can cause dripping and drooping if it gets too hot. Reel Dimensions: Reel Diameter: 195mm (7.68") Hub Diameter: 95mm (3.74") Spindle Diameter: 38mm (1.50") Reel Width: 80mm (3.15")

Premium 3D Printer Filament PLA 3MM 1kg/spool, Red

Premium 3D Printer Filament PLA 3MM 1kg/spool, Red

54.99 USD

Premium 3D Printer Filament PLA 3MM 1kg/spool, Red Compatible Devices Premium 3D Printer Filament PLA 3MM 1kg/spool, Red Get outstanding 3D printing results when you use 3.0mm PLA 3D Printer Filament from 123inkcartridges! PLA is a good choice for a printing material if you are looking for high accuracy and high resolution. It extrudes at lower temperatures, does not require a heated base, and has a very low shrinkage rate (0.3%). PLA is harder than ABS, but is therefore also a bit more brittle. Additionally, PLA is a plant-based plastic, which means that it is biodegradable and gives off a slightly sweet odor, like roasting corn. This 1 Kg spool features a thickness of 3.0mm ±0.10mm, with a roundness variation of only 0.03mm. It has a nominal processing temperature of 185° C (365°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. The negatives of using PLA is that it is vulnerable to degradation from moisture, sunlight, and heat. Additionally, it is more prone to overheating during processing, which can cause dripping and drooping if it gets too hot.   Reel Dimensions: Reel Diameter: 195mm (7.68") Hub Diameter: 95mm (3.74") Spindle Diameter: 38mm (1.50") Reel Width: 80mm (3.15")

Premium 3D Printer Filament ABS 1.75MM 1kg/spool, Fluorescent Yellow

Premium 3D Printer Filament ABS 1.75MM 1kg/spool, Fluorescent Yellow

54.99 USD

Premium 3D Printer Filament ABS 1.75MM 1kg/spool, Fluorescent Yellow Compatible Devices ABS is one of the most commonly used filament types in 3D printing. It has a high tensile strength and good overall toughness. It has a low density and is softer than PLA, which means lower weight and lower cost when printing large models. Hardness is such that no white dot appears when bending. This 1 Kg spool features a thickness of 1.75mm ±0.10mm, with a roundness variation of only 0.05mm. It has a nominal processing temperature of 230° C (446°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. Reel Dimensions: Reel Diameter: 195mm (7.68") Hub Diameter: 95mm (3.74") Spindle Diameter: 38mm (1.50") Reel Width: 80mm (3.15")

Premium 3D Printer Filament ABS 1.75MM 1kg/spool, Silver

Premium 3D Printer Filament ABS 1.75MM 1kg/spool, Silver

54.99 USD

Premium 3D Printer Filament ABS 1.75MM 1kg/spool, Silver Compatible Devices ABS is one of the most commonly used filament types in 3D printing. It has a high tensile strength and good overall toughness. It has a low density and is softer than PLA, which means lower weight and lower cost when printing large models. Hardness is such that no white dot appears when bending. This 1 Kg spool features a thickness of 1.75mm ±0.10mm, with a roundness variation of only 0.05mm. It has a nominal processing temperature of 230° C (446°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. Reel Dimensions: Reel Diameter: 195mm (7.68") Hub Diameter: 95mm (3.74") Spindle Diameter: 38mm (1.50") Reel Width: 80mm (3.15")

Premium 3D Printer Filament ABS 1.75MM 1kg/spool, Gold

Premium 3D Printer Filament ABS 1.75MM 1kg/spool, Gold

54.99 USD

Premium 3D Printer Filament ABS 1.75MM 1kg/spool, Gold Compatible Devices ABS is one of the most commonly used filament types in 3D printing. It has a high tensile strength and good overall toughness. It has a low density and is softer than PLA, which means lower weight and lower cost when printing large models. Hardness is such that no white dot appears when bending. This 1 Kg spool features a thickness of 1.75mm ±0.10mm, with a roundness variation of only 0.05mm. It has a nominal processing temperature of 230° C (446°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. Reel Dimensions: Reel Diameter: 195mm (7.68") Hub Diameter: 95mm (3.74") Spindle Diameter: 38mm (1.50") Reel Width: 80mm (3.15")

Premium 3D Printer Filament ABS 1.75MM 1kg/spool, Blue

Premium 3D Printer Filament ABS 1.75MM 1kg/spool, Blue

54.99 USD

Premium 3D Printer Filament ABS 1.75MM 1kg/spool, Blue Compatible Devices ABS is one of the most commonly used filament types in 3D printing. It has a high tensile strength and good overall toughness. It has a low density and is softer than PLA, which means lower weight and lower cost when printing large models. Hardness is such that no white dot appears when bending. This 1 Kg spool features a thickness of 1.75mm ±0.10mm, with a roundness variation of only 0.05mm. It has a nominal processing temperature of 230° C (446°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. Reel Dimensions: Reel Diameter: 195mm (7.68") Hub Diameter: 95mm (3.74") Spindle Diameter: 38mm (1.50") Reel Width: 80mm (3.15")

Premium 3D Printer Filament ABS 1.75MM 1kg/spool, Pink

Premium 3D Printer Filament ABS 1.75MM 1kg/spool, Pink

54.99 USD

Premium 3D Printer Filament ABS 1.75MM 1kg/spool, Pink Compatible Devices ABS is one of the most commonly used filament types in 3D printing. It has a high tensile strength and good overall toughness. It has a low density and is softer than PLA, which means lower weight and lower cost when printing large models. Hardness is such that no white dot appears when bending. This 1 Kg spool features a thickness of 1.75mm ±0.10mm, with a roundness variation of only 0.05mm. It has a nominal processing temperature of 230° C (446°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. Reel Dimensions: Reel Diameter: 195mm (7.68") Hub Diameter: 95mm (3.74") Spindle Diameter: 38mm (1.50") Reel Width: 80mm (3.15")

Velleman VM8201 STAND-ALONE CONTROLLER FOR 3D PRINTER

Velleman VM8201 STAND-ALONE CONTROLLER FOR 3D PRINTER

78.91 USD

Fully operate your 3D printer with this module! No computer needed (slicing of 3D object and saving to SD-card still needs to be done on a computer)., Prints .GCODE files that are saved on a regular SD-card (SD-card NOT INCLUDED)., Encoder based control., Real time temperature display and control of the extruder and heated bed temperature., Connect to the K8200 controller board with the included flat cable, no extra power supply needed., Enclosure can be printed using .STL file available from Velleman K8200 website., Fully assembled and tested unit. Connection cable requires soldering., SD card slot, Reset button., 4 x 20 character LCD display with backlight., Dimensions: 80 x 50 x 45 mm / 3.15 x 1.96 x 1.77

Monoprice Premium 3D Printer Filament 1.75MM 0.1kg/spool  Cleaning Filament

Monoprice Premium 3D Printer Filament 1.75MM 0.1kg/spool Cleaning Filament

21.94 USD

Keep the nozzles and extruders on your 3D printer printing like new using this 1.75mm Cleaning Filament from Monoprice!It is a good idea to periodically clean the nozzles and extruders on your 3D printer to ensure that they feed filament smoothly and evenly. It is also good to clean when switching filament colors or material types. This cleaning filament is designed to adhere to any stray material left in the nozzle and remove it along with the cleaning filament.To clean using this filament; simply print about 12" of material. It prints at a wide 160 ~ 260°C temperature range.

XYZprinting da Vinci Jr. 1.0 FFF (Fused Filament Fabrication) PLA Single Nozzle 3D Printer

XYZprinting da Vinci Jr. 1.0 FFF (Fused Filament Fabrication) PLA Single Nozzle 3D Printer

219.99 USD

XYZprinting da Vinci Jr. 1.0 FFF (Fused Filament Fabrication) PLA Single Nozzle 3D Printer Series: da Vinci Part Number: da Vinci Jr. 1.0 Number of Extruders: 1 Build Material: PLA Filament Filament Diameter: 1.75mm Connectivity: USB 2.0 / SD Card / WiFi Systems are compatible with SDHC cards up to 32GB in size Interface: USB 2.0, SD card (32G MAX) Operation System Requirements: Windows 7 above (for PC) Mac OSX 10.8 above 64-bit (for Mac) Note: Stardard VGA driver on operating system, or a graphics card doesn't support OpenGL 2.1, may cause unknown error in XYZware.

Wiiboox One Mini Desktop 3D Printer, Single Extruder, 100 Micron

Wiiboox One Mini Desktop 3D Printer, Single Extruder, 100 Micron

979.0 EUR

Wiiboox One Mini Desktop 3D Printer, Single Extruder, 100 Micron Series: One Part Number: CCP0000011 Number of Extruders: 1 Body Material: Metal Frame w/ Acrylic Covers Chassis Material: Metal Frame w/ Acrylic Covers Build Material: Build Material: PLA/ABS, Platform material:Acrylic With Tape Positioning Precision: 2.5 microns(z-axis), 11 microns (x-axis and y-axis) Filament Diameter: 1.75mm

Artifex 2 Duo 3D Printer - Fully Assembled

Artifex 2 Duo 3D Printer - Fully Assembled

1931.91 EUR

Artifex 2 Duo 3D Printer - Fully Assembled Series: Artifex 2 Part Number: ARTIFEX2D-BA Number of Extruders: 2 Build Material: PLA, ABS, NinjaFlex, HIPS, PVA Positioning Precision: X/Y - 12.5micron (0.0005 in), Z - 0.66micron (0.000026in) Filament Diameter: 1.75mm Cartridge Capacity: PLA, ABS, NinjaFlex, HIPS, PVA Connectivity: USB, LCD (SD Card)

Artifex 2 Duo 3D Printer - Complete Kit

Artifex 2 Duo 3D Printer - Complete Kit

1554.03 EUR

Artifex 2 Duo 3D Printer - Complete Kit Series: Artifex 2 Part Number: ARTIFEX2D-BC Number of Extruders: 2 Build Material: PLA, ABS, NinjaFlex, HIPS, PVA Positioning Precision: X/Y - 12.5micron (0.0005 in), Z - 0.66micron (0.000026in) Filament Diameter: 1.75mm Cartridge Capacity: PLA, ABS, NinjaFlex, HIPS, PVA Connectivity: USB, LCD (SD Card)

Artifex 2 3D Printer - Complete Kit

Artifex 2 3D Printer - Complete Kit

1412.33 EUR

Artifex 2 3D Printer - Complete Kit Series: Artifex 2 Part Number: ARTIFEX2-BC Number of Extruders: 1 Build Material: PLA, ABS, NinjaFlex, HIPS, PVA Positioning Precision: X/Y - 12.5micron (0.0005 in), Z - 0.66micron (0.000026in) Filament Diameter: 1.75mm Cartridge Capacity: PLA, ABS, NinjaFlex, HIPS, PVA Connectivity: USB, LCD (SD Card)

FlashForge Dreamer 3D Printer

FlashForge Dreamer 3D Printer

998.99 USD

Flashforge Dreamer 3D Printer Series: Dreamer Number of Extruders: 2 Positioning Precision: 0.0001" on Z axis, 0.0004" on XY plane Cartridges Compatible: ABS/PLA/Dissolvable Filament Compatibl Interface: USB, WiFi, SD card, App connectivity 2GB SD Card Printer Dimensions: 18.40" x 15.00" x 12.60" Printer Weight: 27.00 lbs.

Print Rite CoLiDo 2.0 3D Printer

Print Rite CoLiDo 2.0 3D Printer

999.99 USD

Print Rite CoLiDo 2.0 3D Printer Part Number: LMD011XQ7J Body Material: Steel Build Material: PLA/ABS Filament Diameter: 1.75mm Connectivity: USB and SD card Operation System Requirements: Window 7, MAC OX, Linus Operation Temperature: 15º - 32ºC (60º - 90ºF) Storage Temperature: 0º - 32ºC (32º - 90ºF)

Monoprice 12131 - 3D Printer Extruder Heating Assembly Replacement

Monoprice 12131 - 3D Printer Extruder Heating Assembly Replacement

77.28 USD

Monoprice 12131 - 3D Printer Extruder Heating Assembly ReplacementThis is a replacment 3D Printer Extruder Heating Assembly for the Monoprice Dual Extrusion ABS/PLA/PVA 3D Printer (PID 11614).This extruder heating assembly melts the 3D filament and extrudes it through the 0.4mm nozzle.

LeapFrog(R) Scout's Goodnight Light

LeapFrog(R) Scout's Goodnight Light

15.99 USD

You can now join Scout and Violet rocketing into outer space using the LeapFrog(R) Scout's goodnight light! You can use it as a flashlight or as a night light with glowing stars shining on your ceiling. This also offers 10 or 20 minutes of bedtimes music or sound. Ages: 9-24 months.

LeapFrog(R) Scout's Count 'N Colors Band

LeapFrog(R) Scout's Count 'N Colors Band

19.99 USD

It's time to get the LeapFrog(R) Scout's count 'n colors band ready to jam! You can play long with Scout on the piano by testing out the cymbals, trombone, saxophone, drums and guitar! Once you get started you can begin to count and learn along with the rhymes. Ages 0-2 years.

LeapFrog(R) Count 'N Crawl Kitty

LeapFrog(R) Count 'N Crawl Kitty

19.99 USD

This LeapFrog(R) count 'n crawl kitty is such a fun toy for your child. It is designed for push-and-play and counting! The keys running down the back help to learn the numbers 1-20 and counting rhymes or use the keys as a keyboard and make your own music! Ages: 9-24 months.

LeapFrog(R) Melody The Musical Turtle

LeapFrog(R) Melody The Musical Turtle

19.99 USD

With the LeapFrog(R) Melody the musical turtle is a great way to work on memory and pre-school skills! Melody has 10 fun musical activities that help you child learn numbers, shapes, colors, and patterns. Plus there are additional games for learning and fun! Ages 2 and up.

LeapFrog(R) Phonics Magnet

LeapFrog(R) Phonics Magnet

19.99 USD

This LeapFrog(R) phonics magnet is easily put on your fridge and lets little hands play with the magnetic letters right away! The magnet allows your child to explore the alphabet by inserting the tiles into the bus that allow them to talk, sing and teach! Ages 2-5 years.

LeapFrog(R) Leaping Letters

LeapFrog(R) Leaping Letters

19.99 USD

This is an easy way to make learning fun and exciting using the LeapFrog(R) leaping letters! Race against the timer to put the letters in alphabetical order before the timer runs out and they POP! An adjustable timer allows all ages to play. Ages: 3-6 years.

LeapFrog(R) Chat & Count Phone

LeapFrog(R) Chat & Count Phone

15.99 USD

Now your little one can have their own phone using the LeapFrog(R) chat and count phone! They can explore up to 15 different activities and all Scout whenever they want! Plus this toy can be connected to online to customize the learning! Ages 0-17.

LeapFrog(R) Musical Rainbow Tea Party

LeapFrog(R) Musical Rainbow Tea Party

21.99 USD

It's time for tea and cake with the LeapFrog(R) musical rainbow tea party! This tea set is a great learning tool for you child as they grow. They can host a tea party while learning songs, colors, matching, and counting. Ages 0 to 3.

LeapFrog(R) Count Along Register

LeapFrog(R) Count Along Register

24.99 USD

You child's imaginary store is open for business using the LeapFrog(R) count along register! Ring up sales as either the cashier or shopper and watch your bagging skills! Otherwise you will hear the crunch of eggs! Ages: 2-4 years.

LeapFrog(R) Number Lovin' Oven

LeapFrog(R) Number Lovin' Oven

24.99 USD

This LeapFrog(R) number lovin' oven lets your child get cooking by frying an egg in the skillet, bake bread, pizza, or cupcakes! While your cooking, the oven sings about counting, sharing, and vocabulary. Ages 2 to 5.

LeapFrog(R) Alpha Pup

LeapFrog(R) Alpha Pup

19.99 USD

This LeapFrog(R) Alpha Pup sings the ABCs and sounds out letters to expose your child to phonics and vocabulary. The buttons are interactive and Alpha Pup's tail wags as he is pulled. Ages: 1-3 years.

Monoprice 3D Printer Extruder Fan Replacement

Monoprice 3D Printer Extruder Fan Replacement

18.3 USD

This is a replacment 3D Printer Extruder Fan for the Monoprice Dual Extrusion ABS/PLA/PVA 3D Printer (PID 11614).This fan helps maintain the extruder at a constant temperature.

Monoprice 3D Printer Belt Pulley Replacement

Monoprice 3D Printer Belt Pulley Replacement

18.9 USD

This is a replacment 3D Printer Belt Pulley for the Monoprice Dual Extrusion ABS/PLA/PVA 3D Printer (PID 11614).This aluminum pulley is used to drive the XYZ axis belts.

Velleman 3D Printer Starter Kits

Velleman 3D Printer Starter Kits

441.01 USD

Velleman 3D Printer Starter KitsDimensions: Unit width: 22.04Unit height: 8.46Unit depth: 10.24Unit weight: 344.27

3D Printer Iduino MEGA2560 Control Board ATmega2560 Development Board

3D Printer Iduino MEGA2560 Control Board ATmega2560 Development Board

26.82 SGD

3D Printer Iduino MEGA2560 Control Board ATmega2560 Development Board Product Sort: Printer Accessories

5pcs XH2.54-2P 2.54mm 70cm Dupont Wire Cable Female to Female 2P for 3D Printer

5pcs XH2.54-2P 2.54mm 70cm Dupont Wire Cable Female to Female 2P for 3D Printer

3.88 AUD

5pcs XH2.54-2P 2.54mm 70cm Dupont Wire Cable Female to Female 2P for 3D Printer Type: Electronic

WIFEB 3MM ABS/PAL 0.3mm Nozzle Fittings RepRap J-head MKIV MKV Hotend For 3D Printer

WIFEB 3MM ABS/PAL 0.3mm Nozzle Fittings RepRap J-head MKIV MKV Hotend For 3D Printer

3905.55 INR

WIFEB 3MM ABS/PAL 0.3mm Nozzle Fittings RepRap J-head MKIV MKV Hotend For 3D Printer

WIFEB 3MM ABS/PAL 0.5mm Nozzle Fittings RepRap J-head MKIV MKV Hotend For 3D Printer

WIFEB 3MM ABS/PAL 0.5mm Nozzle Fittings RepRap J-head MKIV MKV Hotend For 3D Printer

55.03 EUR

WIFEB 3MM ABS/PAL 0.5mm Nozzle Fittings RepRap J-head MKIV MKV Hotend For 3D Printer

WIFEB 3D Printer Teensylu V0.8 Board Hi3D RepRap Prusa Mendel Printer Driver Board

WIFEB 3D Printer Teensylu V0.8 Board Hi3D RepRap Prusa Mendel Printer Driver Board

40.19 EUR

WIFEB 3D Printer Teensylu V0.8 Board Hi3D RepRap Prusa Mendel Printer Driver Board

3D Printer DIY Kit for Reprap Prusa Mendel i3 Self-assembly DIY Suit Accessories

3D Printer DIY Kit for Reprap Prusa Mendel i3 Self-assembly DIY Suit Accessories

651.04 AUD

3D Printer DIY Kit for Reprap Prusa Mendel i3 Self-assembly DIY Suit Accessories